minn kota deckhand 40 problems

What are Minn Kota Deckhand 40 Problems?- Explained it In-details!

Introduction 

Having problems in Minn kota deckhand is normal. So many people face different kinds of problems. But some of us are still not aware of the exact problems.

Are you asking about what is Minn Kota deckhand 40 problems

The Minn Kota deckhand 40 has a switch up down issue. Anchor capability is another very prevalent difficulty. The anchor capability is imprinted, which is a significant disadvantage. It has no impact on lowering the anchor. When you praise up or down, no clicks occur, and the machine does not reset.

I’ll just give you a glimpse. If you have little time then go through the article, and you will not regret it. Let’s go! 

What are the Minn Kota Deckhand 40 Problems?

Minn Kota deckhand has some common problems which most people face after using it for a while. Fixing those problems is not that much difficult. You just need to what is the actual problem and from where it starts. After that, you can solve it on your own. 

Problem 1: Anchor doesn’t Lower 

At the stroke of a button, you may instantly raise and lower your anchor. The DeckHand 40 includes an anchor capability of 40-pound. And 100 feet of 800-lb test nylon rope is pre-spooled. You can position the universal davit near the base of the deckhand. Or it can be in a remote location on the boat deck. 

If you looking for good quality nylon rope, then you should try these products: 

Product-1
Product-2 

These nylon rope is really strong and their durability is amazing.

Davit also horizontally, stows the anchor preventing anchor swing. The anchor shackle enables easy switching between anchors. A unique anti-drug mechanism detects the bottom, allowing for controlled drifting.

It’s powered by a 12-volt battery. The remote attachment (sold separately) enables 25′ corded remote operation. DH 40 is intended for use with anchors holding 20 lbs but no more than 40 lbs. The Minn Kota Deckhand 40 anchor lifts but does not lower the anchor. 

Problem 2: Power Switch Doesn’t Work

When you press the down switch, nothing happens, there’s no clicking. And the machine doesn’t reset. This is a very big problem if the power switch doesn’t work properly. However. don’t relate it with the motor not spinning in the right way issues.

It will cause danger. Mine does not power down; it only powers up. It is dragged down by the weight of the anchors. 

How to Solve Minn Kota Deckhand 40 Problem? 

You have already got a slight idea on the ways to solve the problems. Here get an elaborate guide. 

Troubleshooting Anchor Doesn’t Lower 

Before we get into the step first learn about the switches. Well there are three places on the switch.

  1. Up is only a temporary posture. To raise the anchor, it must be held in place.
  2. The centre position is incorrect.
  3. The down posture is not transitory. It’ll click and stick.

Here learn the steps –

  • The anchor winch will drop the anchor to the bottom. And after that stop, if the switch is left in the down position.
  • As the boat pulls on the anchor, the line will slip out of the down position. To feed line out and position the boat, use the down switch position.
  • Again in position, turn the anchor switch to the middle position (off). And the winch will no longer feed the line.
  • In the down switch position, the winch must have resistance on the line. Because it will feed the outline, such as an electric winch.
  • Those who have the remote switch: If you leave the anchor switch at the winch in the down position. And then use the remote switch to raise the anchor. The anchor will receive feedback as soon as you release the remote control.
  • For one switch to operate properly, the other switch must be in the centre (off) position.

If you have the same setup, 40 anchor winches and 40 chains then you shouldn’t go overboard. As you may be putting lot of strain on your engine remember you’re not only raising the chain.

But the boat’s drift will put additional strain on the motor. I’m not sure what size yacht you’re putting it on. Hence anything larger than 40 would seem excessive. 

In addition, you should utilize the rocker switch back by yourself. Since It can simply raise and lower the anchor and drift back as needed.

Both the microswitch and the circuit board should be replaced with new ones. It’s still performing the same thing where there’s no cut-off. But when the anchor hits the deckhand! I’m scared it’ll eventually strip some gears! 

However, don’t mess up with the replacing method with replacing trolling motor. We replace it when the trolling motor has no power.

Troubleshooting Power Switch Doesn’t work

According to the Minn Kota repair shop, it require a new circuit board and a new switch. It takes three hours the repair it. Which is to change the circuit board but had to order the up/down switch. It just installed the switch, and the problem persists. It can be raised but not lowered. 

These are the troubleshooting guide. Now time to show you some faqs

FAQs 

How big of an anchor do I need?

It is advised that you use a scope of 7:1 for an anchor. This means that you should utilize 7 feet of road for every foot of water depth. To anchor in 10 feet of water, for example, you would use 70 feet of line.

Is it possible to drop anchor in the middle of the ocean?

The response is a resounding ‘no.’ Because of the depth, it is not possible to anchor in the middle of the ocean. To ensure adequate holding, you should have at least 7 times more line out than water below your boat.

What exactly is a wildcat on a ship?

The wildcat is a hollow, vertical drum-like contraption with ridges surrounding it. It is constructed in such a way that they will contact the anchor chain’s links. The wildcat is designed to be tightly connected to the shaft. Otherwise, it can be free to revolve around it.

What would be termed a ground tackle?

Ground tackle applies to all of the components of an anchor package. It is located between both the boat and the anchor. If you just use line, the ground tackle is known as the anchor Rhode or line. Anchoring terminology includes the scope and catenary of the phrase. 

Wrapping Up 

I hope I could answer all your queries about the Minn Kota deckhand 40 problems. If you face any type of problem just follow the instructions. And after that, you can do it on your own. Just keep patient throughout the work. 

But if you couldn’t understand the process, in that case, you can always ask for professional help. They will complete your work within an hour. 

I think I’m done! I hope you enjoy this article and learn things. Good to see you here. Goodbye. Till then take care.

Leave a Comment

Your email address will not be published.

Scroll to Top