mercury 40 hp 4 stroke problems

Mercury 40 HP 4 Stroke Problems [5 Solutions Explained]

Introduction

Made up your mind to go fishing with your favorite boat ride? It seems your 4-stroke engine just has refused to start! If this is your scenario, you have come to the right place! 

Sitting around and getting mad won’t be any help to solve this! We show you the fixes here.

So, what are the Mercury 40 HP 4 stroke problems?

Several problems like the incompatibility of the engine, and overheating are there. Sometimes, a lack of fuel efficiency might put your boat into serious trouble. Along with that, you might require more repairing of its different parts. Moreover, its lubrication system needs periodic maintenance.

But that’s not all! However, this article recognizes the common problems that many users have met! And, it delivers feasible solutions.

Let’s not beat the bush around and dig this deeper right now-

Mercury 40 HP 4 Stroke Problems and Possible Solutions

Enough of scratching the surface! Now it’s time to dig out the real problem related to this engine. And, by the end of this section, ideal solutions are at your doorstep.

Problem 1: Incompatibility With Smaller Boats

We know four-stroke engines come heavier than other popular strokes. You can not suit the Mercury 40 HP 4 strokes while adjusting with a smaller boat. 

A clear weight imbalance between the boat and engine will be visible due to this misfit. Similarly, Suzuki 200 HP outboard issues also draw this incompatibility.  

Solution

So, always picking the stroke variety is ideal once your boat size is confirmed. We suggest you pick the two-stroke-based engines such as Mercury or even Yamaha. 

This approach will make your outboard engine choice worthy enough. You are getting much time to think if you should get Mercury 4 strokes or not. 

Problem 2: Boat Engine Sputtering Issue and Eventually Losing Power

This issue is so common happening with the Mercury 40 HP 4 Stroke engine. Seeing the engine sputtering out basically indicates the decrement of its strength. 

In the meantime, happening this so frequently and repetitively leads us to something more dangerous. Filter problem or spoiled plugs is the key reason behind this. 

As a result, sooner or later the boat motor starts losing its power. Engines inside outboards like hangkai outboard issues also indicate having this problem!

Solution 

Every owner should vent the engine chamber completely before resuming. If you don’t do that, a clogged filter might appear in the picture.

Meanwhile, the odds of mixing between the gas and water- we all know. So, avoid leaving the fuel tank empty. Rather, you need to fill the tank as much as possible.

Users mostly face this condensation trouble after leaving the boat for no operation. And, the more you keep away working on it, the more condensation chances are there. 

We suggest you get a fuel stabilizer. After that, leave the tank for 3 or 4 months longer if required! Nothing harmful will be happening. Along with that, you might choose a simple path to prevent sputtering. 

Cleaning and changing the spark plugs in time is the key here. Changing these spark plugs should be done according to the motor usage. 

As we mention spark plugs, here are some recommended picks-

Product 1
Product 2

Also, don’t forget to change the fuel filter on a regular basis. So, try to reinstall the in-line fuel filter. 

What if you have not got one? Then, clearing debris from the filter component will be enough. Along with that, drain the water that was stored earlier.

Before doing that, simply check the manufacturer from where you have bought this. Spark plug details will indicate when is the perfect time to replace them. 

As the first sign of deterioration appears, you should work from that period. Along with these, keeping a simple toolbox on board carrying basic installation instruments is ideal.

The secondary problem is that sometimes you can just get bad fuel. While fuel is supplied to stations, the last ones receiving the fuel might get trash quality. 

As a result, fuel might get stored at the bottom of the tank. And, during the full-fledged operation, it might cause trouble. Along with that, if you leave the fuel tank empty, condensation might start building up. 

Problem 3: Engine Not Starting

What else can be bigger than the engine failures? Well, lack of fuel efficiency comes first in this circumstance in the Mercury 40 HP engines. So, the first thing you should do is to focus on the fuel system. 

Also, you can’t understand the pain until turning on the ignition key and hearing no sound. This is quite frustrating indicating your temporary engine failure. 

To keep it active and running with full control, the ignition key must produce a sound. However, the absence of necessary steps at the right time might result in long-run engine failure.

Solution

Check if any portion of the fuel is being kept in the engine for so long. So, you should not avoid it while finding this circumstance. The fuel inside the Mercury 4-stroke engine might go through a chemical reaction. 

As an end product, you might find fuel-producing ethanol. As a result, the prevention of the engine running comes into the picture. 

Also, there might be some blockages on filters all caused by dirt. Along with that, chances of line and carburetor blocking exist too. 

Second of all, look for the kill button. Check if the shifter is staying at the neutral position or not. Along with that, focus your attention on the starter control. 

Sometimes, the ignition switch might relax the fitting automatically. As a result, it might allow the whole switch control to pivot with the key. Simply, get some screws to tighten the retention nut.

Problem 4: Overheating Issue Inside the Boat Engine

Sensitive engines require heat balancing so that they might work for a long time uninterruptedly. Meanwhile, temperature gauges are available to measure the heat. 

While you go through checking this device, have you seen the needle rising? Then, your engine might have overheated. Along with that, it confirms having a cooling coil with inadequate water flow. 

Unfortunately, most of the outboard engines do not come with radiators. As a result, the chances of relying on water increase. However, it’s not the ideal way to keep your engine cooler. 

Suddenly stopping water flow brutally shows how ineffective this is to rely on! That’s where the overheat takes place and results in engine failure. 

However, in some circumstances like Yamaha F115 4-Stroke problems also show this characteristic. So, you might find it unable to start. Meanwhile, Mercury outboard engines are more painless to operate. 

Solution

Among 40, 50, and 60 HP variants, Mercury 40 HP is not that top-notch in performance. And, chances of overheating issues are so common. 

First, investigate the cause. Check the raw water input. You might slow down the water flow by the slack hose clamps or burst hoses. It might heal the damaging moisture around the engine.

Problem 5: Required More Potential Repairing 

The more parts existing in a system, the more repairs the system might require. 

And, we already know building a 4 stroke engine requires more parts behind this for functioning. So, this case is obvious in the four-stroke engine, isn’t it?

Meanwhile, its lubrication system might require more periodic maintenance. Can you guess why? As long as they come with more parts, they might demand more lubricant to cover. 

Solution

Utilizing a 2-stroke engine might be an option. It might require fewer parts to operate compared to a 4-stroke. And, you will explore more power generation here than a 4-stroke engine of the same horsepower. 

A 2-stroke engine utilizes two pistons only for one revolution of crankshaft power generation. As a result, more power generation is possible. 

Meanwhile, cooling, sealing, cleaning, serving, and lowering friction are the key securities for moving parts. And, managing such five steps is not an easy task. 

That’s why periodic maintenance is a must. So, check these steps regularly whether these have been completed or not. 

FAQs

Are Mercury 4 Strokes Dependable?

Though Mercury comes with 2 strokes-based variants too, its 4 stroke engines are more dependable. Meanwhile, having an electronic fuel injection system makes this device more reliable. Along with that, you will find it much more fuel-efficient. As a result, hitting the long run can be accomplished.

Why Is My Outboard Slow-moving?

Having a spun prop comes first as the key reason behind causing this. It makes the powerboat struggling to gain suitable speed at full throttle. This occurs when the connection between the boat propeller and mounting shaft gets damaged. That’s why you find the rubber inserts begin revolving alone.

Yamaha or Mercury Outboard- Which One Is Better?

Well, both are great at their specific fields. Yamaha comes greener and nature-friendly outboard between these two. And, it provides two electric motors while Mercury has to offer none. Meanwhile, Mercury is the ideal pick for getting a long-lasting warranty of more than eight years.

Final Words

Now you know the solutions to Mercury 40 HP 4 stroke problems. We’ve tried to cover common problems regarding this. 

We hope that you might have got the idea about what you require at present. 

Still, if you have any queries, let us know! Thanks for staying put this far!

Leave a Comment

Your email address will not be published.

Scroll to Top