evinrude timing procedure

Evinrude Timing Procedure: Briefed with Easy 7 Steps

Introduction

It’s no secret that Evinrude outboard motors are some of the best known and most respected on the market. A motor’s timing may need to be altered from time to time.

In addition, it’s needed to replace the water pump and impeller. Using an engine’s link rods, the timing can be fine-tuned. Setting the Evinrude’s timing should only take about an hour.

So, what are the steps of the Evinrude timing procedure you need to follow?

When a timer base or stator is out of sync it may make ticking noises or start inconsistently. For troubleshooting, set the spark advance. Then set the crankshaft. Find the spring and move the throttle. Mark the flywheel as you set the timer.  Warm up the engine. Make sure the boat is tethered. 

To find out more, read the entire article.

Troubleshooting of Evinrude Timing Procedure

When a timer base or stator is out of sync, you may hear or see ticking noises or have an inconsistent start. In this section, we’ll talk about them. These are also the symptoms of a bad trigger outboard.

The Sound of Time Passing Incessantly

Pulleys are joined to the timing belt, which you can see if you look closely. There will be a ticking noise as the belt wears out. Don’t spend your time if you notice something like that while running the engine.

No Power to the Engine

A worn-out belt might cause this symptom. But if the engine won’t start at all, it means the belt has been broken or removed completely.

To make matters worse, the accident might occur even if the engine is on. This can harm the spark plug, crank bearings, fuel pump, push rods, rocker arms, or valves.

Instances of Misfire

Misfiring is another common sign. One or more cylinders will not burn properly. If the trigger does not transmit a signal to the power pack in time.

When you hear misfire, you know you’ve reached that point. In this case, you should be prepared for two outcomes. It’s possible for the ignition to be advanced or retarded in two different ways.

Overheating

Engine overheating may be a result of faulty ignitions. This is also an indicator of bad timing on the outboard.

Low-Input

Voltage regulation and ignition timing issues. You’ve probably already figured out that it reduces the engine’s power. The outboard motor operates slower with a heavier load.

An Inadequate Start

There may be an issue with the timing of the onboard engine. If you have difficulty starting it or hear knocking noises while trying to do so.

Using either too early or too late an ignition generates a number of issues. There’s also a shaky beginning.

Detailed Instructions for Evinrude Timing

Are you positive that all three cylinders are receiving fuel? Motor won’t idle with one cylinder down. However, it can operate with the other two cylinders’ spark advance increased if necessary.

Let’s check the step-by-step procedure-

Step 1: Set the Spark Advance

Setting the spark advance to 16-18 BTDC is all you need to do in terms of timing. The idle time should be taken care of automatically. Motors are supposed to be running then. 

The remaining plug wires should be grounded to prevent sparks from igniting the fuel. It may be spewed out of the plug holes.

Step 2: Set the Crankshaft

Set the crankshaft, then have someone turn the engine over for you. Spray some carb cleaning into each carb’s throat as you crank the engine. Check the johnson outboard shift linkage adjustment

It’s possible that only one of your carbs is supplying fuel. In this case you’ll need to replace it.

Step 3: Find the Spring

Remove the link rod from the plastic piece that connects to the roller of the fuel injector. Look up at the arms. On top of a piece of plastic, you’ll find a spring that causes the timer to spin.

Step 4: Move the Throttle 

Let this spring cool down completely before moving on. When it comes to the rod on the carb, the rod ½ inch snaps back on. 

But you need a 10 mm gap between the huge lump of plastic and the roller. These keep the timer from advancing.

When you move the engine, you’ll see that the throttle advances ahead of the timer. When you slide the throttle 1/4 inch, the timer starts.

Step 5: Set the Timer

Set the timing to maximum advance now. Make sure the timer is pulled as far back as it will go. As this is where you want to see 18 btdc. 

No need to worry about idle time. Since that will be taken care of by the system itself.

Step 6: Mark the Flywheel

Once the fuel supply has been disconnected, write 18/19 on the flywheel with a marker. Then connect a timing light, and set the throttle to full. 

Turn the key to engage the bolt beneath the flywheel. Secure it once you’re done.

Step 7: Warm up the Engine

Now that you’ve gotten the timing somewhat perfect. It’s time to hook up the fuel and fire up the beast.  

It’s best if you can get the boat in the water and under some kind of load. Let the engine warm-up for a few minutes now, even if it’s running at a high speed. You may want to adjust the slow speed on the outboard.

For the timing procedure, gather these timing tools-

Product 1
Product 2

 Once the engine is warmed up, check the timing again. but this time make sure the boat is tethered or you can do it while driving. 

Avoid running the engine solely on carb cleaner due to the lack of lubrication. Only use it for testing.

FAQs

How do outboard motor points work?

Two-point contacts transmit a magneto spark to the ignition points on a Johnson outboard engine. It’s just like any other ignition point. The camshaft rotates to open and close the valves. This causes the point contacts to open and close.

For an outboard condenser, how do you do a test?

A condenser case (negative lead) and a wire termination should be touched by the metre leads (positive lead). The metre should deflect swiftly toward zero (discharge). Then slowly return to infinity when the battery recharges the condenser.

Is Repairing Outboard Timing Problems Expensive?

Take into account the boat mechanic’s hourly charge. Which is often between $70 and $10. As well as the cost of the parts that need to be replaced. In the case of a defective trigger, the service fee of an expert would only be about $250.

Conclusion

We are clear about your confusion about on evinrude timing procedure here. Your engine’s longevity will suffer if you don’t fix the timing fault, so please do it right now.

When combustion-related parts are damaged, the engine’s final failure results. Pay close attention to everything around you. Take action if you even have the slightest inkling that something is amiss.

Go boating and have fun!

Leave a Comment

Your email address will not be published.

Scroll to Top